Your here: Home / Network / Hardware Specific / Airlive / WLA-9000AP


Airlive WLA-9000AP
Airlive WLA-9000APa.jpg

Homepage

WLA-9000AP

Wikipedia

?

dd-wrt

v24-sp1

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: Activation Required.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs[edit | edit source]

Fixme.gif This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Atheros AR5312
MIPS Rev = ?
CPU Speed = 220MHz
Bus = ?
Flash Type = Parallel
Flash Chip = ?
Flash Size = 8MB
Max Firmware Size = 7995392 bytes
RAM Size = 32MB
RAM Chip = ?
nvram Size = ?
Switch = M 88E6061-LAJ1 B56991.2 1642 A1P
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-WAN 2-LAN
Wired Standard = IEEE 802.3?/3af
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = Yes
Power = 5.5V/2.5A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = v.24 SP2 - build 11003
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features = ?

Radio

Wireless Radio = Atheros
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = ?
 802.11n Draft = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[edit | edit source]

Flashing[edit | edit source]

Fixme.gif This section is in need of cleanup!

Upgrading[edit | edit source]

Fixme.gif This section is in need of cleanup!

Reverting[edit | edit source]

Fixme.gif This section is in need of cleanup!

Revert files

JTAG/Serial Info[edit | edit source]

JTAG[edit | edit source]

JTAG Pinouts[edit | edit source]
Fixme.gif This section is in need of cleanup!
JTAG Recovery[edit | edit source]
Fixme.gif This section is in need JTAG Recovery Instructions!

Serial[edit | edit source]

Serial Pinouts[edit | edit source]
o1 VCC
o2 RXD
o3 N/C
o4 N/C
o5 TXD
o6 GND
Hyper terminal Setup in Windows XP[edit | edit source]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[edit | edit source]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[edit | edit source]
Fixme.gif This section is in need of Serial Recovery Instructions!

vlan Info[edit | edit source]

Fixme.gif This section is in need of cleanup!

Pictures[edit | edit source]

Airlive WLA-9000AP Airlive WLA-9000AP

Airlive WLA-9000AP Airlive WLA-9000AP

FCC Pictures[edit | edit source]

Fixme.gif This section is in need of cleanup!

Notes[edit | edit source]


Hardware Modification[edit | edit source]


Community content is available under CC-BY-SA unless otherwise noted.