Your here: Home / Network / Hardware Specific / Asus / RT-N12 B1


Asus RT-N12 B1
Asus RT-N12a.jpg

Homepage

RT-N12

Wikipedia

?

dd-wrt

WIP

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs[edit | edit source]

Fixme.gif This section is in need of cleanup!

Platform

What command generates the following output???

Serial Num. = ?
FCC ID = MSQ-?
CPU Type = Broadcom BCM5357
MIPS Rev = B0
CPU Speed = 300MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 8MB
Max Firmware Size = 3801088 bytes
RAM Size = 32MB
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100M-WAN 4-10/100M-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/1A
Color of LEDs = ?
Size = 179 X 119 X 37(L x W x H)mm
USB = No
Serial Port = 1
JTAG Port = 1
Supported by TJTAG/Version = ?
Supported by dd-wrt as of =
[[1]]
dd-wrt K2.4 Support = NO
dd-wrt K2.6 Support = YES
Special Features = ?

Radio

Wireless Radio = Broadcom
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = ?
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[edit | edit source]

Fixme.gif This section is in need of cleanup!

Flashing[edit | edit source]

Fixme.gif This section is in need of cleanup!

Upgrading[edit | edit source]

Fixme.gif This section is in need of cleanup!

Reverting[edit | edit source]

Fixme.gif This section is in need of cleanup!

JTAG/Serial Info[edit | edit source]

JTAG[edit | edit source]

JTAG Pinouts[edit | edit source]
Fixme.gif This section is in need of cleanup!
JTAG Recovery[edit | edit source]
Fixme.gif This section is in need JTAG Recovery Instructions!

Serial[edit | edit source]

Serial Pinouts[edit | edit source]
Fixme.gif This section is in need of cleanup!
Hyper terminal Setup in Windows XP[edit | edit source]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[edit | edit source]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[edit | edit source]
Fixme.gif This section is in need of Serial Recovery Instructions!

vlan Info[edit | edit source]

Fixme.gif This section is in need of cleanup!

Pictures[edit | edit source]

Fixme.gif This section is in need of cleanup!


FCC Pictures[edit | edit source]

Fixme.gif This section is in need of cleanup!


Notes[edit | edit source]

Hardware Modification[edit | edit source]

Community content is available under CC-BY-SA unless otherwise noted.