Your here: Home / Network / Hardware Specific / Belkin / F5D8235-4 v20xx

Belkin F5D8235-4 v20xx
Belkin F5D8235-4 a
N+ Wireless Router










Not Supported


Not Supported



NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.


Fixme This section is in need of cleanup!


Serial Num. = ?
FCC ID = K7SF5D8235-4B
CPU Type = Ralink RT3052F
MIPS Rev = ?
CPU Speed = 380MHz
Bus = ?
Flash Type = Parallel
Flash Chip = MX 29LV640DBTC-90G
Flash Size = 8MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = 2x Winbond W9812G6IH-6
nvram Size = ?
Switch = RTL8366RB
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = U-Boot
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/1.5A
Color of LEDs = ?
Size = ?
USB = USB 2.0
Serial Port = 1
JTAG Port = No
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = WIP
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = ?


Wireless Radio = Ralink RT3052F (SoC)
WLAN DSP processor = ?
Antenna Connector Type = External Fixed
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit



Fixme This section is in need of cleanup!


JTAG/Serial InfoEdit


JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!


Serial PinoutsEdit
pin 1 Power  ---- its a square pin
pin 2 Tx
pin 3 Rcv
pin 4 Gnd
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

USB InfoEdit

Fixme This section is in need of cleanup!

vlan InfoEdit

Fixme This section is in need of cleanup!


Belkin F5D8235-4 v20xx b Belkin F5D8235-4 v20xx c

FCC PicturesEdit

Belkin F5D8235-4 v20xx FCC a Belkin F5D8235-4 v20xx FCC b Belkin F5D8235-4 v20xx FCC c

Belkin F5D8235-4 v20xx FCC d Belkin F5D8235-4 v20xx FCC e Belkin F5D8235-4 v20xx FCC f

Belkin F5D8235-4 v20xx FCC g Belkin F5D8235-4 v20xx FCC h Belkin F5D8235-4 v20xx FCC i

Belkin F5D8235-4 v20xx FCC j Belkin F5D8235-4 v20xx FCC k Belkin F5D8235-4 v20xx FCC l

Belkin F5D8235-4 v20xx FCC m Belkin F5D8235-4 v20xx FCC n


Hardware ModificationEdit

Community content is available under CC-BY-SA unless otherwise noted.