Your here: Home / Network / Hardware Specific / Belkin / F7D8301 v1
(Play N600 HD Wireless Dual-Band N+ Router)
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
File:Belkin_F7D8302_v1_a.jpg Play N600 HD Wireless Dual-band N Router |
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs[]
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = K7SF7D4301V1 ? CPU Type = ? MIPS Rev = ? CPU Speed = ? Bus = ? Flash Type = ? Flash Chip = ? Flash Size = ? Max Firmware Size = ? RAM Size = ? RAM Chip = ? nvram Size = ? Switch = ? Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = ? Wired Standard = IEEE 802.3? boot_wait = ? bootloader = ? Flash Card Socket/Type = ? SD/MMC Mod Support = ? MiniPCI slots = ? PoE = ? Power = ? Color of LEDs = ? Size = ? USB = ? Serial Port = ? JTAG Port = ? Supported by TJTAG/Version = ? Special Features = ?
Radio
Wireless Radio = ? WLAN DSP processor = ? Antenna Connector Type = ? Wireless Standard = ??? IEEE 802.11a/b/g/n WiFi Operating Frequency = ? ??? 802.11n = up to 300Mbps ??? 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps ??? 802.11b = 1, 2, 5.5, 11Mbps ??? 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of Interest[]
Flashing[]
Upgrading[]
Reverting[]
JTAG/Serial Info[]
JTAG[]
JTAG Pinouts[]
This section is in need of cleanup!
JTAG Recovery[]
This section is in need JTAG Recovery Instructions!
Serial[]
Serial Pinouts[]
J3 |> [+ TX RX -] or 1. 3.3 2. TX 3. RX 4. GND
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - Communication - HyperTerminal Enter a name for the connection, Click ok Choose com port you adapter is plugged into, Click ok Set: Bits per second = 115200 Data Bits = 8 Parity = none Stop bits = 1 Flow control = none Click ok Click File - Save As, and select a place to save it to so you don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Mincom setup in Linux[]
After installing minicom, run it with -s flag for setup (sudo minicom -s) Under "Serial Port Setup": Use 'A' to set the serial device (ie. /dev/ttyUSB0) Use 'E' to set the Bps/Par/Bits Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Save as dfl
Serial Recovery[]
1. Clear the nvram 2. Type ifconfig and you should get '=0', then it succeeded. 3. Note the ip address listed and netmask address. 4. After you have used the ifconfig command wait a minute or two. 5. In your web browser got to the IP address noted in step 4. 6. Upload DD-WRT mini image or original firmware. Example: CFE> nvram erase CFE> ifconfig =0 CFE>
TFTP Recovery
Coming Soon
USB Info[]
vlan Info[]
Pictures[]
FCC Pictures[]
Notes[]
F7D8301 v1 Chips
Broadcom Dual band (2.4 GHz/5GHz) Wireless Radio: BCM4718A1KFBG
Broadcom Smart Gigabit Switch: BCM53115SKFBG
EtronTech DDR2 32MX16BIT SDRAM: EM68B16CWPA-25h
cFeon NVRAM: EN29lV640B-90TIP
Sticker over cFeon NVRAM: WG8117F22 2-LF-AK
Hardware Modification[]