Your here: Home / Network / Hardware Specific / Buffalo / WHR-G300N v1.0

Buffalo WHR-G300N v1.0
Buffalo WHR-G300N
AirStation™ Nfiniti™ Wireless-N Router


WHR-G300N v1.0






WHR-G300N v1.0


Not Supported


Not Supported


Not Supported


Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.


Fixme This section is in need of cleanup!


Serial Num. = ?
FCC ID = FDI-09101538-0
CPU Type = Ralink RT3052F PA93150B2 083STE
MIPS Rev = ?
CPU Speed = 384MHz
Bus = ?
Flash Type = Parallel
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = 2 x 16MB hynix 829E C HY57V281620FTP-6
nvram Size = ?
Switch = Ralink RT3052F (SoC)
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/2A
Color of LEDs = ?
Size = 5.5" x 5.0" x 1.0"
USB = No
Serial Port = ?
JTAG Port = Yes
Supported by TJTAG 3.02 = ?
Supported by dd-wrt as of = v24 SP2 - build 13744 - 20100126
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = ?


Wireless Radio = Ralink RT3052F (SoC)
WLAN DSP processor = N/A
Antenna Connector Type = 2x2 MIMO high power external antenna
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n Draft 2.0 = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities =?

Links of Interest


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!

JTAG/Serial Info


JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!


Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

vlan Info

Fixme This section is in need of cleanup!


Buffalo WHR-G300N b

FCC Pictures

Buffalo WHR-G300N v1.0 FCC a Buffalo WHR-G300N v1.0 FCC b Buffalo WHR-G300N v1.0 FCC c

Buffalo WHR-G300N v1.0 FCC d Buffalo WHR-G300N v1.0 FCC e Buffalo WHR-G300N v1.0 FCC f

Buffalo WHR-G300N v1.0 FCC g Buffalo WHR-G300N v1.0 FCC h Buffalo WHR-G300N v1.0 FCC i

Buffalo WHR-G300N v1.0 FCC j Buffalo WHR-G300N v1.0 FCC k Buffalo WHR-G300N v1.0 FCC l

Buffalo WHR-G300N v1.0 FCC m Buffalo WHR-G300N v1.0 FCC n


Hardware Modification

Community content is available under CC-BY-SA unless otherwise noted.