InfoDepot Wiki
Advertisement

Your here: Home / Network / Hardware Specific / Cisco-Linksys / Cisco RV110W


Cisco RV110W
Cisco RV110W a.jpg
Wireless-N VPN Firewall

Homepage

Cisco RV110W

Wikipedia

Linksys Routers

WikiDevi

?

dd-wrt

Status Unknown

OpenWRT

Status Unknown

Tomato

Status Unknown

TomatoUSB

Status Unknown

Gargoyle

Status Unknown

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs[]

Fixme.gif This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = N89-RV110W
CPU Type = Broadcom BRCM5357
MIPS Rev = ?
CPU Speed = ?
Bus = ?
Flash Type = Serial
Flash Chip = ?
Flash Size = 16MB
Max Firmware Size = ?
RAM Size = 64MB
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = ?
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = ?
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = ?
WLAN DSP processor = ?
Antenna Connector Type = ?2x2 mimo
Wireless Standard = ??? IEEE 802.11a/b/g/n
WiFi Operating Frequency = ?
 ??? 802.11n = up to 300Mbps
 ??? 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 ??? 802.11b = 1, 2, 5.5, 11Mbps
 ??? 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[]

Flashing[]

Fixme.gif This section is in need of cleanup!

Upgrading[]

Fixme.gif This section is in need of cleanup!

Reverting[]

Fixme.gif This section is in need of cleanup!

JTAG/Serial Info[]

JTAG[]

JTAG Pinouts[]
Fixme.gif This section is in need of cleanup!
JTAG Recovery[]
Fixme.gif This section is in need JTAG Recovery Instructions!

Serial[]

Serial Pinouts[]
Fixme.gif This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[]
Fixme.gif This section is in need of Serial Recovery Instructions!

USB Info[]

Fixme.gif This section is in need of cleanup!

vlan Info[]

Fixme.gif This section is in need of cleanup!

Pictures[]

alt text alt text

FCC Pictures[]

alt text alt text alt text

alt text alt text alt text

alt text alt text

Notes[]


Hardware Modification[]


Advertisement