Your here: Home / Network / Hardware Specific / D-Link / DIR-632


D-Link DIR-632
File.JPG

Homepage

?

Wikipedia

?

dd-wrt

Not Supported

OpenWRT

Not Supported

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs[edit | edit source]

Fixme.gif This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = ?
MIPS Rev = ?
CPU Speed = ?
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = ?
Max Firmware Size = ?
RAM Size = ?
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = ?
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = ?
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = ?
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = ??? IEEE 802.11a/b/g/n
WiFi Operating Frequency = ?
 ??? 802.11n = up to 300Mbps
 ??? 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 ??? 802.11b = 1, 2, 5.5, 11Mbps
 ??? 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[edit | edit source]

Fixme.gif This section is in need of cleanup!

Flashing[edit | edit source]

Fixme.gif This section is in need of cleanup!

Upgrading[edit | edit source]

Fixme.gif This section is in need of cleanup!

Reverting[edit | edit source]

Fixme.gif This section is in need of cleanup!

JTAG/Serial Info[edit | edit source]

JTAG[edit | edit source]

JTAG Pinouts[edit | edit source]
Fixme.gif This section is in need of cleanup!
JTAG Recovery[edit | edit source]
Fixme.gif This section is in need JTAG Recovery Instructions!

Serial[edit | edit source]

Serial Pinouts[edit | edit source]
Fixme.gif This section is in need of cleanup!
Hyper terminal Setup in Windows XP[edit | edit source]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[edit | edit source]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[edit | edit source]
Fixme.gif This section is in need of Serial Recovery Instructions!

USB Info[edit | edit source]

Fixme.gif This section is in need of cleanup!

vlan Info[edit | edit source]

Fixme.gif This section is in need of cleanup!

Pictures[edit | edit source]

Fixme.gif This section is in need of cleanup!

FCC Pictures[edit | edit source]

Fixme.gif This section is in need of cleanup!

Notes[edit | edit source]


Hardware Modification[edit | edit source]


Community content is available under CC-BY-SA unless otherwise noted.