FANDOM


Your here: Home / Network / Hardware Specific / D-Link / DIR-685


D-Link DIR-685
D-Link DIR-685 a
Xtreme N Storage Router

Homepage

DIR-685

Wikipedia

?

WikiDevi

DIR-685

dd-wrt

Not Supported

OpenWRT

Not Supported

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

SpecsEdit

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = RRK-WMPND02A1
Industry Canada ID = 4833A-WMPND02A1
CPU Type = Storlink SL3516
MIPS Rev = ?
CPU Speed = ?
Bus = ?
Flash Type1 = ?
Flash Chip1 = Spansion S29GL256P11TFI01
Flash Size1 = 32MB
Flash Type2 = ?
Flash Chip2 = ?
Flash Size2 = 8MB
Max Firmware Size = ?
RAM Size = 64MB
RAM Chip = Hynix?
nvram Size = ?
Switch = Realtek RTL8366SR
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN
Wired Standard = IEEE 802.3/3u/3ab
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = 1
PoE = ?
Power = ?
Color of LEDs = ?
Size = ?
USB = 2x USB 2.0
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = SATA

Radio

Wireless Radio = Alpha Networks WMP-N08
WLAN DSP processor = Ralink RT2880
Antenna Connector Type = 2x2
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = ?
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

Fixme This section is in need of cleanup!

FlashingEdit

Fixme This section is in need of cleanup!

UpgradingEdit

Fixme This section is in need of cleanup!

RevertingEdit

Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit

JTAGEdit

JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!

SerialEdit

Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

USB InfoEdit

Fixme This section is in need of cleanup!

vlan InfoEdit

Fixme This section is in need of cleanup!

PicturesEdit

Fixme This section is in need of cleanup!

FCC PicturesEdit

Fixme This section is in need of cleanup!

NotesEdit


Hardware ModificationEdit


Community content is available under CC-BY-SA unless otherwise noted.