InfoDepot Wiki
Advertisement

Your here: Home / Network / Hardware Specific / Doodle Labs / DLM101


Doodle Labs DLM101
Doodle Labs DLM101a.jpg

Homepage

DLM101

Wikipedia

?

dd-wrt

?

OpenWRT

?

Tomato

?

TomatoUSB

Not Supported

Gargoyle

?

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs[]

Fixme.gif This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Atheros AR2315/AR2316
MIPS Rev = ?
CPU Speed = 180MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 16MB
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = VLAN Support VLAN pass through
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN/LAN AUTO MDI/MDX
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = 9V ~ 18V
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = DLM101 v.24 SP2 - build 12517
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = ?

Radio (ath0)

Wireless Radio = Atheros
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g @24dbm
WiFi Operating Frequency = 2.3GHz - 2.7GHz
Channel Bandwidth = 5MHz/10MHz/20MHz/40(Optional)MHz
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[]

Fixme.gif This section is in need of cleanup!

Flashing[]

Fixme.gif This section is in need of cleanup!

Upgrading[]

Fixme.gif This section is in need of cleanup!

Reverting[]

Fixme.gif This section is in need of cleanup!

JTAG/Serial Info[]

JTAG[]

JTAG Pinouts[]
Fixme.gif This section is in need of cleanup!
JTAG Recovery[]
Fixme.gif This section is in need JTAG Recovery Instructions!

Serial[]

Serial Pinouts[]
Fixme.gif This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[]
Fixme.gif This section is in need of Serial Recovery Instructions!

USB Info[]

Fixme.gif This section is in need of cleanup!

vlan Info[]

Fixme.gif This section is in need of cleanup!

Pictures[]

Fixme.gif This section is in need of cleanup!

FCC Pictures[]

Fixme.gif This section is in need of cleanup!

Notes[]


Hardware Modification[]