Your here: Home / Network / Hardware Specific / Cisco-Linksys / E1000 v2.0

Linksys E1000 v2.0
Linksys E1000a
Wireless-N Router




Linksys E1000


Linksys E1000 v2.0


Linksys E1000 v2.0


Status Unknown


Status Unknown


Status Unknown


Status Unknown

NOTE: Requires K2.6, Do not flash anything else.
NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.


Fixme This section is in need of cleanup!


Serial Num. = CVN1
FCC ID = Q87-E1000V2
CPU Type = Broadcom BCM5357B0KFBG (BCM5357B)
MIPS Rev = ?
CPU Speed = 300MHz
Bus = ?
Flash Type = Serial
Flash Chip = MX 25L3205D
Flash Size = 4MB
Max Firmware Size = 3801088 bytes
RAM Size = 32MB
RAM Chip = Hynix H5DU2562GTR
nvram Size = 32kb
Switch = Broadcom BCM5357B0KFBG (BCM5357B)
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/0.5A
Color of LEDs = ?
Size = 7.95" x 1.34" x 6.3" (202 x 34 x 160 mm)
USB = No
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG 3.02 = ?
Supported by dd-wrt as of = 16758
dd-wrt K2.4 Support = No
dd-wrt K2.6 Support = Yes
Special Features = ?

Radio (wl0)

Wireless Radio = Broadcom BCM5357B0KFBG (BCM5357B)
WLAN DSP processor = Broadcom BCM5357B0KFBG (BCM5357B)
Antenna Connector Type = Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n Draft = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit


JTAG PinoutsEdit
Fixme This section is in need of cleanup!
JTAG RecoveryEdit
Fixme This section is in need JTAG Recovery Instructions!


Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!


Pic's from barryware.

Linksys E1000b Linksys E1000c Linksys E1000d

Linksys E1000e Linksys E1000f Linksys E1000g

FCC PicturesEdit

Linksys E1000 v2.0 FCCa Linksys E1000 v2.0 FCCb Linksys E1000 v2.0 FCCc

Linksys E1000 v2.0 FCCd

With Switch SampleEdit

Linksys E1000 v2.0 FCCe ws Linksys E1000 v2.0 FCCf ws Linksys E1000 v2.0 FCCg ws

Linksys E1000 v2.0 FCCh ws Linksys E1000 v2.0 FCCi ws Linksys E1000 v2.0 FCCj ws

Linksys E1000 v2.0 FCCk ws Linksys E1000 v2.0 FCCl ws

Without Switch SampleEdit

Linksys E1000 v2.0 FCCm wos Linksys E1000 v2.0 FCCn wos Linksys E1000 v2.0 FCCo wos

Linksys E1000 v2.0 FCCp wos Linksys E1000 v2.0 FCCq wos Linksys E1000 v2.0 FCCr wos


Hardware ModificationEdit

Community content is available under CC-BY-SA unless otherwise noted.