Advertisement

Your here: Home / Network / Hardware Specific / Cisco-Linksys / E1200 v1.0


Linksys E1200 v1.0
Linksys E1200 a.jpg

Wireless-N Router

Homepage

E1200

Wikipedia

Linksys Routers

WikiDevi

Linksys E1200 v1

dd-wrt

Linksys E1200 v1

OpenWRT

Status Unknown

Tomato

Status Unknown

TomatoUSB

Status Unknown

Gargoyle

Status Unknown

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

 Fixme.gif  This section is in need of cleanup!

Platform

Serial Num. = 1081
FCC ID = Q87-E1200
Industry Canada ID = 3839A-E1200
CPU Type = Broadcom BCM5357B0
MIPS Rev = ?
CPU Speed = 300MHz
Bus = ?
Flash Type = ?
Flash Chip = Macronix MX25L3206E
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = Winbond W9425G6JH-5
nvram Size = ?
Switch = Broadcom BCM5357B0 (SoC)
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = ?
PoE = No
Power = 12VDC/0.5A
Color of LEDs = ?
Size = 7.43" x 1.23" x 5.97"
USB = Possible Mod to add
Serial Port = YES
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = Broadcom BCM5357B0 (SoC)
WLAN DSP processor = ?
Antenna Connector Type = 2x2, Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4 GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Flashing

 Fixme.gif  This section is in need of cleanup!

Upgrading

 Fixme.gif  This section is in need of cleanup!

Reverting

 Fixme.gif  This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
 Fixme.gif  This section is in need of cleanup!
JTAG Recovery
 Fixme.gif  This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
1 = vcc (3.3v)
2 = tx
3 = rx
4 = n/c
5 = ground
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
 Fixme.gif  This section is in need of Serial Recovery Instructions!

vlan Info

 Fixme.gif  This section is in need of cleanup!

Pictures

Linksys E1200 b.jpg
alt text
Linksys E1200 c.jpg
alt text
Linksys E1200 d.jpg
alt text

Linksys E1200 e.jpg
alt text
Linksys E1200 f.jpg
alt text

FCC Pictures

 Fixme.gif  This section is in need of cleanup!

Notes


Hardware Modification


Community content is available under CC-BY-SA unless otherwise noted.