InfoDepot Wiki

READ MORE

InfoDepot Wiki
Register
Advertisement

Your here: Home / Network / Hardware Specific / Cisco-Linksys / Linksys WAP54G v1.1


File:Linksys WAP54G.jpg

WARNING - DD-WRT was not originally intended to be loaded on a WAP unit. It was found that it will run but it is a tricky unit to load and have function correctly. Below are a compilation of methods/instructions to assist you with creating a DD-WRT loaded WAP unit.
NOTE: Requires Micro, Do not flash anything else.
NOTE: Requires VINT, Do not flash anything else.
NOTE: Requires K2.4, Do not flash anything else.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs[]

Platform

Serial Num. = MDG1
FCC ID = PKW-WAP54G
CPU Type = Broadcom BCM4702KPB
MIPS Rev = ?
CPU Speed = 125MHz
Bus = ?
Flash Type = Parallel
Flash Chip = AMD AM29LV320DB-90EI
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 8 or 16MB
RAM Chip = 2x Dynachips D98SD64 16AH-60310A
nvram Size = ?
Switch = ?
Port-based vlan = No
802.1q vlan = No
Ethernet Port Count = 1-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = 1
PoE = No
Power = 12V/0.5A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = No
JTAG Port = ?
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = ?
dd-wrt K2.4 Support = Micro VINT only
dd-wrt K2.6 Support = No
Special Features = 7 leds on front panel and 4MB Flash, Micro VINT only

Radio (wl0)

Wireless Radio = MiniPCI Broadcom BCM4306KFB
WLAN DSP processor = ?
Antenna Connector Type = RP-TNC
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = 2.4GHz
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[]

Flashing[]

Upgrading[]

Fixme This section is in need of cleanup!

Reverting[]

Fixme This section is in need of cleanup!

JTAG/Serial Info[]

JTAG[]

JTAG Pinouts[]
Fixme This section is in need of cleanup!
JTAG Recovery[]
Fixme This section is in need JTAG Recovery Instructions!

Serial[]

Serial Pinouts[]
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[]
Fixme This section is in need of Serial Recovery Instructions!

Pictures[]

Fixme This section is in need of cleanup!

FCC Pictures[]

Linksys WAP54G v1 Linksys WAP54G v1 Linksys WAP54G v1

Linksys WAP54G v1 Linksys WAP54G v1 Linksys WAP54G v1

Linksys WAP54G v1 Linksys WAP54G v1 Linksys WAP54G v1

Notes[]


Hardware Modification[]


Advertisement