InfoDepot Wiki

READ MORE

InfoDepot Wiki
Register
Advertisement

Your here: Home / Network / Hardware Specific / Cisco-Linksys / Linksys WRH54G


File:Linksys_WRH54Ga.jpg

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = Q87-WRH54G
CPU Type = Broadcom BCM5354
MIPS Rev = ?
CPU Speed = 240MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 2MB
Max Firmware Size = ?
RAM Size = 8MB
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-WAN 4-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = 12V/0.5A
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = v24 micro rc7 - 9063
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features =?

Radio (wl0)

Wireless Radio = Broadcom
WLAN DSP processor = ?
Antenna Connector Type = RP-TNC
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = ?
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Fixme This section is in need of cleanup!

Flashing

Thanks to Eko for getting the device supported.
Special thanks to a9988cd for donation, Tornado and redhawk0 for all the work and testing.

Don't use this image on any other router - for WRH54G only !

Linksys WRH54G is now supported by dd-wrt. No need to replace cfe, but you alwayays need to use special firmware built for wrh54g only. Even for later GUI upgrades.

  1. Restore to defaults
  2. Open upgrade page, select dd-wrt.v24-12548_WRH54G_micro.bin (or other special wrh image)
  3. Upgrade
  4. When it comes back, be sure to press reset button for 5 s to restore dd-wrt's factory defaults
      • that's it ***

Upgrading

Fixme This section is in need of cleanup!

Reverting

  1. Download WRH54G firmware from Linksys
  2. Restore to defaults
  3. Open upgrade page, select the firmware
  4. Upgrade
  5. When it comes back, be sure to press reset button for 5 s to restore Linksys's factory defaults
      • that's it ***

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

Pictures

alt text alt text

FCC Pictures

alt text alt text alt text

alt text alt text alt text

alt text alt text alt text

alt text

Notes


Hardware Modification


Advertisement