InfoDepot Wiki

READ MORE

InfoDepot Wiki
Register
Advertisement

Your here: Home / Network / Hardware Specific / Cisco-Linksys / WRT110 v1.0


Linksys Zazai

File:Linksys_WRT110_a.jpg
RangePlus Wireless Router

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs[]

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = Q87-WRT110
Industry Canada ID = 3839A-WRT110
CPU Type = Ralink's RT2700
MIPS Rev = ?
CPU Speed = ?
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 16MB
RAM Chip = ?
nvram Size = ?
Switch = ICplus IP175C
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = 12V/1A
Color of LEDs = ?
Size = 8.0" x 6.3" x 1.4"
USB = ?
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = Ralink's RT2700
WLAN DSP processor = Ralink RT2720
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = ?
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[]

Flashing[]

Fixme This section is in need of cleanup!

Upgrading[]

Fixme This section is in need of cleanup!

Reverting[]

Fixme This section is in need of cleanup!

JTAG/Serial Info[]

JTAG[]

JTAG Pinouts[]
Fixme This section is in need of cleanup!
JTAG Recovery[]
Fixme This section is in need JTAG Recovery Instructions!

Serial[]

Serial Pinouts[]
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[]
Fixme This section is in need of Serial Recovery Instructions!

USB Info[]

Fixme This section is in need of cleanup!

vlan Info[]

Fixme This section is in need of cleanup!

Pictures[]

Fixme This section is in need of cleanup!

FCC Pictures[]

alt text alt text alt text

alt text alt text alt text

alt text alt text alt text

alt text alt text alt text

alt text alt text alt text

alt text alt text alt text

Notes[]


Hardware Modification[]


Advertisement