InfoDepot Wiki

READ MORE

InfoDepot Wiki
Register
Advertisement

Your here: Home / Network / Hardware Specific / Cisco-Linksys / WRT160N v2.0


File:Linksys_WRT160N_v2.0a.jpg

NOTE: This divice is not supported by dd-wrt.

Specs[]

Fixme This section is in need of cleanup!

Platform

Serial Num. = CSE11
FCC ID = Q87-WRT160NV2
CPU Type = Ralink RT2880F NH47960E0 0827ST
MIPS Rev = ?
CPU Speed = 266MHz
Bus = ?
Flash Type = Parallel
Flash Chip = EON EN29LV320AB-70TCP 16CG02A 0712KDA
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 16MB
RAM Chip = 2x Samsung 834 K4S641632K-UC60
Switch = RTL8306SD 86F71Q1 GB27B
nvram Size = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = U-Boot
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/1A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = Yes
JTAG Port = Yes (micro)
Supported by TJTAG/Version = ?
Special Features = ?

Radio (wl0)

Wireless Radio = Ralink RT2820L CV63560C0 0801ST
WLAN DSP processor = ?
Antenna Connector Type = Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4Ghz
 802.11n Draft = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[]

Flashing[]

Fixme This section is in need of cleanup!

Upgrading[]

Fixme This section is in need of cleanup!

Reverting[]

Fixme This section is in need of cleanup!

JTAG/Serial Info[]

JTAG[]

JTAG Pinouts[]
Fixme This section is in need of cleanup!
JTAG Recovery[]
Fixme This section is in need JTAG Recovery Instructions!

Serial[]

Serial Pinouts[]
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[]
Fixme This section is in need of Serial Recovery Instructions!

vlan Info[]

Fixme This section is in need of cleanup!

Pictures[]

alt text

FCC Pictures[]

Fixme This section is in need of cleanup!

alt text alt text alt text

alt text alt text alt text

alt text alt text alt text

alt text alt text

Notes[]


Hardware Modification[]

Advertisement