FANDOM


Your here: Home / Network / Hardware Specific / Cisco-Linksys / WRT330N v1.0


Linksys WRT330N v1.0
Linksys WRT330N v1.0a
Wireless-N Gigabit Gaming Router

Homepage

WRT330N

Wikipedia

WRT330N

WikiDevi

?

dd-wrt

Not Supported

OpenWRT

Not Supported

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported

NOTE: 3rd party Linux firmware is not supported on the Ubicom processor.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Ubicom IP5160U
MIPS Rev = ?
CPU Speed = 275MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 4MB
Max Firmware Size = ?
RAM Size = 32MB
RAM Chip = ?
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN
Wired Standard = 802.3/3u/3ab
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = 12V/1.0A
Color of LEDs = Power Internet, Ethernet (1-4), Wireless, Security
Size = ?
USB = ?
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = ?
WLAN DSP processor = ?
Antenna Connector Type = Fixed 1.5dBi
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Fixme This section is in need of cleanup!

Flashing

Fixme This section is in need of cleanup!

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Linksys WRT330N v1.0b

FCC Pictures

Linksys WRT330N v1.0 FCCa Linksys WRT330N v1.0 FCCb Linksys WRT330N v1.0 FCCe

Linksys WRT330N v1.0 FCCc Linksys WRT330N v1.0 FCCd Linksys WRT330N v1.0 FCCf

Linksys WRT330N v1.0 FCCg Linksys WRT330N v1.0 FCCh Linksys WRT330N v1.0 FCCi

Linksys WRT330N v1.0 FCCj Linksys WRT330N v1.0 FCCl

Notes


Hardware Modification


Community content is available under CC-BY-SA unless otherwise noted.