Your here: Home / Network / Hardware Specific / Cisco-Linksys / WRT51AB v1.0
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
File:Linksys_WRT51ABa.jpg |
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs[]
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = PKW-WRT51AB CPU Type = Broadcom BCM4702KPB TN0210 P10 15138 (BCM4702) MIPS Rev = ? CPU Speed = 125MHz Bus = ? Flash Type = Parallel Flash Chip = Intel E28F320 J3A110 52040375 Flash Size = 4MB Max Firmware Size = ? RAM Size = 32MB RAM Chip = 2x GLT5640L16-7TC 219 PVB1C76015 nvram Size = ? Switch = Broadcom BCM5325A2KQM RT0231 P12 63164 Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-WAN 4-LAN Wired Standard = IEEE 802.3? boot_wait = ? bootloader = CFE Flash Card Socket/Type = No SD/MMC Mod Support = No MiniPCI slots = 2 PoE = No Power = 5V/2.5A Color of LEDs = 24- Leds Size = ? USB = No Serial Port = 1 JTAG Port = 1 Supported by TJTAG/Version = ? Supported by dd-wrt as of = WIP Will Require Jtag for first flash! dd-wrt K2.4 Support = ? dd-wrt K2.6 Support = ? Special Features = ?
Radio (wl0)
Wireless Radio = Broadcom BCM4301KPF CS0224 P20 63355.6 S WLAN DSP processor = ? Antenna Connector Type = Fixed Wireless Standard = IEEE 802.11b/g WiFi Operating Frequency = ? 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Radio (wl1)
Wireless Radio = Atheros WLAN DSP processor = ? Antenna Connector Type = Fixed Wireless Standard = IEEE 802.11a WiFi Operating Frequency = ? 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of Interest[]
Flashing[]
Upgrading[]
Reverting[]
JTAG/Serial Info[]
JTAG[]
JTAG Pinouts[]
This section is in need of cleanup!
JTAG Recovery[]
This section is in need JTAG Recovery Instructions!
Serial[]
Serial Pinouts[]
This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - Communication - HyperTerminal Enter a name for the connection, Click ok Choose com port you adapter is plugged into, Click ok Set: Bits per second = 115200 Data Bits = 8 Parity = none Stop bits = 1 Flow control = none Click ok Click File - Save As, and select a place to save it to so you don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial Recovery[]
This section is in need of Serial Recovery Instructions!
vlan Info[]
Pictures[]
FCC Pictures[]
Notes[]
Hardware Modification[]