InfoDepot Wiki

READ MORE

InfoDepot Wiki
Register
Advertisement

Your here: Home / Network / Hardware Specific / Cisco-Linksys / WRT54GS v5.1


File:Linksys_WRT54GS.jpg

NOTE: Requires Micro, Do not flash anything else.
NOTE: Requires K2.4, Do not flash anything else.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs[]

Fixme This section is in need of cleanup!

Platform

Serial Num. = CGN8
FCC ID = Q87-WT54GV40
CPU Type = Broadcom BCM5352
MIPS Rev = ?
CPU Speed = 200MHz
Bus = ?
Flash Type = Parallel
Flash Chip = ?
Flash Size = 2MB
Max Firmware Size = 1769472 bytes
RAM Size = 16MB
RAM Chip = ?
nvram Size = ?
Switch = ?
nvram Size = ?
vlan Support = ?
Ethernet Port Count = 1-10/100-WAN 4-10/100-LAN
Wired Standard = IEEE 802.3/3u
boot_wait = ?
bootloader = CFE
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = No
Power = 12V/0.5A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = 2
JTAG Port = Yes
Supported by TJTAG 3.02 = Yes
Supported by dd-wrt as of = ?
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features =?

Radio

Wireless Radio = ?
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = ?
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest[]

Flashing[]

These instructions are for the WRT54gS version v.5 and v.6. NOTE THE S. The instructions for the router Wrt54g WITHOUT the S are above.

IN SPITE OF SOME OTHER INSTRUCTIONS ELSEWHERE, YOU REALLY NEED TO CREATE A CUSTOM VX Image for your router. If you don’t you will get a generic mac address on your router and a generic mac address will mean most ISP won’t let you connect to the internet. Here is how to do it properly

There is good information at the scorpiontek site: http://www.scorpiontek.org/portal/content/view/27/36

Go to this thread and download the zipped files in GV5Flash.zip: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=58231

  1. Read the peacock announcement found here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Do a Hard reset or 30/30/30 on the router according to note 1 of the peacock announcement (30/30/30)
  3. Set a static IP on your computer to 192.168.1.7
  4. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in.
  5. Unzip the file you downloaded and place it in a location you can easily find on your computer
  6. Unzip the VXImgToolGui.zip file to the same folder as where you placed the other files you downloaded
  7. Delete the vxworks_prep_v03.bin file
  8. Go to this location and download the vxworks_prep_GS_v03.bin file: http://www.dd-wrt.com/dd-wrtv2/downloads/others/wrt54gv5%20flashing/vxworks_prep_gs_v03.zip
  9. Click on the VXImgToolGui.exe program
    1. Make sure the top button is on the right for WRT54GS, not the left for WRT54G.
    2. Put the mac address from the bottom of your router in the box that says "Desired Mac Address"
    3. Click on the three dots next to "output image" and save the file as My54gsImage.bin in the same folder as everything else is located.
  10. Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in)
  11. Open your browser to 192.168.1.1 but putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  12. Enter "root" as the username and "admin" as the password
  13. Go to administration and firmware upgrade
  14. Navigate to the folder that you are using, and select vxworks_prep_GS_v03.bin
  15. Hit upgrade.
  16. Wait for FIVE FULL MINUTES. Go for a walk. Don't you TOUCH that router for FIVE MINUTES.
  17. When five full earth minutes have passed, power cycle the router
  18. Refresh your browser window. If you get a blank window, clear your browser cache. NOW you should be in the MANAGEMENT MODE window.
  19. Select the My54gImage.bin file that you created. Hit upgrade.
  20. Wait for the "Upgrade Success" message, and then WAIT FIVE FULL MINUTES again. Don't TOUCH your router.
  21. Start tftp.exe
    1. Enter 192.168.1.1 as the address in the top box of tftp.exe
    2. Leave the password blank
    3. Select the 12548 Newd_Micro.bin firmware
    4. Set retries to 99.
    5. Power cycle the router
    6. Count to 2
    7. Hit upgrade
  22. When you get a success, wait FIVE FULL minutes.
  23. When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.
  24. When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another Hard reset or 30/30/30 on the router.
  25. Reset your computer ethernet connection to auto IP and auto DNS
  26. Check for recommended builds here.

Upgrading[]

If dd-wrt is already on the router follow these instructions. If stock firmware is on the router follow the flashing instructions.

  1. Check for recommended builds here first.
  2. Set your computer to a static IP of 192.168.1.7. (or to whatever subnet the router is on) Disable all firewalls and security. Disable wireless on your computer and only have the router connected to the flashing computer by the ethernet cable between the two.
  3. Hard reset or 30/30/30 (If the router supports it, if not, reset to defults in the GUI) prior to flashing. Wait. Check for password page on re-login and change password.
  4. Flash firmware. You can use the webgui except if you have a belkin router. (For belkin use tftp.exe to flash)
  5. Wait...at least three minutes. Lights should return to normal. See important2, below. Failing to wait is how most people brick their routers.
  6. Do a power cycle of the router. (Unplug the cord, count to 30 and plug it back in.)
  7. Wait for the lights to return to normal usually about 2 minutes.
  8. Hard reset or 30/30/30 again (If the router supports it, if not, reset to defults in the GUI). Wait. Check for the password page and re-login to change the password. Then you can reconfigure your settings manually.
  9. Once configured set your computer back to autoIP and autoDNS.

Important1: This Hard reset or 30/30/30 works fine for Asus router, but you do have to power cycle after the reset.

Important2: After you flash the firmware, and before you do the hard reset, the router will be building some nvram settings. YOU MUST WAIT FOR THIS TO FINISH PRIOR TO DOING ANYTHING WITH THE ROUTER INCLUDING A HARD RESET. Usually, you can tell when this process is completed by the WAN light coming on, but it does take several minutes. Go have a beer. There are starting to be more and more people who BRICK their routers by not waiting until the nvram is rebuilt, PRIOR to doing a hard reset. YOU NEED TO WAIT!

Reverting[]

Fixme This section is in need of cleanup!

JTAG/Serial Info[]

JTAG[]

JTAG Pinouts[]
Fixme This section is in need of cleanup!
JTAG Recovery[]
Fixme This section is in need JTAG Recovery Instructions!

Serial[]

Serial Pinouts[]
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP[]
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP[]
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery[]
Fixme This section is in need of Serial Recovery Instructions!

vlan Info[]

Fixme This section is in need of cleanup!

Pictures[]

Fixme This section is in need of cleanup!

FCC Pictures[]

Notes[]


Hardware Modification[]


Advertisement