Your here: Home / Network / Hardware Specific / Netgear / WG602 v3.0

Netgear WG602 v3.0
Netgear WG602 v3.0a






Netgear WG602 v3.0


Netgear WG602 v3.0




Not Supported



NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.


Fixme This section is in need of cleanup!


Serial Num. = ?
CPU Type = Broadcom BCM5350
MIPS Rev = ?
CPU Speed = 200MHz
Bus = ?
Flash Type = ?
Flash Chip = Intel TE 28F160C3 BDBD70
Flash Size = 2MB
Max Firmware Size = ?
RAM Size = 8MB
RAM Chip = EtronTech EM638425TS-6
nvram Size = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-WAN/LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = 7.5V/1A
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = Yes
JTAG Port = Yes
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = v24 RC-5 (11/05/07) micro - build 8332
dd-wrt K2.4 Support = Yes
dd-wrt K2.6 Support = No
Special Features = initial flash: use Tftp flash

Radio (wl0)

Wireless Radio = Broadcom
Antenna Connector Type = SMA
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = ?
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit

Fixme This section is in need of cleanup!


Someone who has this router should write a proper wiki entry on how to upgrade, but until that is done, here is a link to some basic information

dd-wrt Firmware Replacement on Netgear WG602v3 Wireless Access Point
Augur 11:34, 30 August 2010 (CEST)

Read This FirstEdit

READ the Peacock Thread first. use the wiki and forums to do research before even contemplating installing dd-wrt
check the WG602v3 works before flashing
check your WG602v3 matches the details in the [Supported Devices page]


the WG602v3 only has 2mb flash memory so can only support the micro builds
BrainSlayer builds (13525) dd-wrt.v24_micro_generic.bin
using [tftp2.exe]

Preparing The WG602v3Edit

  1. connect the WG602v3 to a computer using a network cable
  2. set static ip of computer to
    • there should be no means of access to any other router or dhcp server or the WG602v3 will not set its default ip address.
  3. perform a [30-30-30 Hard Reset]
  4. in browser go to L:admin P:password and check it is the default netgear setup

Installing dd-wrtEdit

  1. on the computer disable firewall and antivirus
  2. run tftp2.exe
    • configure as follows
    • Server to
    • password leave blank
    • pick the firmware
    • set rety to 50
  3. open a command prompt and type in ping -t
  4. unplug power lead from router
  5. replug power lead into router
  6. the instant you get a ping response from the router click Upgrade
    • if it doesn't work try unplugging again (timing matters)
    • stop pinging the router (ctrl-c)

  • (very important) wait 5-7 minutes after you get the success message before doing anything. recomend you walk away and get a drink

After Install. Initial Preparation Before UseEdit

  1. reconfigure the static ip of the computer to
  2. in browser go to
    • if you get the dd-wrt web gui password change page perform a power cycle on the router
  3. when the web gui comes up again perform a 30-30-30 hard reset
  4. wait for gui to come up again
    • change default username and password
    • close browser
  5. open browser and load the gui again. you should now have the status screen
    • login and configure
  6. remember to re-enable firewall, antivirus, and dhcp on the computer


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit


Pinout for the UART1 connector

Looking from the backside of the device the pinout of UART1 (J5) is

   *      Pin 1 = 3,3V
   *      Pin 2 = RxD
   *      Pin 3 = TxD
   *      Pin 4 = Gnd

USB InfoEdit

Fixme This section is in need of cleanup!

vlan InfoEdit

Fixme This section is in need of cleanup!


Netgear WG602 v3.0b

FCC PicturesEdit

Fixme This section is in need of cleanup!


Hardware ModificationEdit

Community content is available under CC-BY-SA unless otherwise noted.