Your here: Home / Network / Hardware Specific / Netgear / WNDR3700
 |
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
|
File:Netgear_WNDR3700a.jpg N600 WIRELESS DUAL BAND GIGABIT ROUTER |
NOTE: Requires K2.6, Do not flash anything else.
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs
This section is in need of cleanup!
Platform
Serial Num. = 100-13948 FCC ID = PY308300092 CPU Type = Atheros AR7161 rev 2 MIPS Rev = ? CPU Speed = 680MHz Bus = ? Flash Type = Serial Flash Chip = ? Flash Size = 8MB Max Firmware Size = ? RAM Size = 64MB RAM Chip = hynix 830A HY5DU561622FTP-D43 nvram Size = ? Switch = RTL8366SR 95E89SE G920B Port-based vlan = Yes 802.1q vlan = No Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN Wired Standard = IEEE 802.3? boot_wait = ? bootloader = u-boot Flash Card Socket/Type = No SD/MMC Mod Support = No MiniPCI slots = No PoE = No Power = 12V/2.5A Color of LEDs = ? Size = 8.8" x 6.0" x 1.2" USB = Yes Serial Port = Yes JTAG Port = Yes Supported by TJTAG/Version = ? Supported by dd-wrt as of = v.24 SP2 - build 14158 - 20100329 dd-wrt K2.4 Support = No dd-wrt K2.6 Support = Yes Special Features = USB, 1000 BaseT (gigabit) switch, Dual-Radio
Radio (ath0)
Wireless Radio = Atheros AR9223 Antenna Connector Type = Internal Wireless Standard = IEEE 802.11b/g/n WiFi Operating Frequency = 2.4GHz 802.11n = up to 300Mbps 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Radio (ath1)
Wireless Radio = Atheros AR9220 Antenna Connector Type = Internal Wireless Standard = IEEE 802.11a/n WiFi Operating Frequency = 5GHz 802.11n = up to 300Mbps 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of Interest
Flashing
The Netgear WNDR3700 is an extremely powerful consumer 802.11 a/b/g/n router, sporting a lightning fast Atheros CPU, lots of RAM, lots of flash space, and capable of high transmit power that even gives 2Wire a run for the money makes this router is ready for the future, and DD-WRT makes it even better. Installation of DD-WRT is very simple and can be done in a few steps.
1. Download DD-WRT for the WNDR3700 from here: ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/08-12-10-r14929/netgear-wndr3700/wndr3700-factory.img
2. Make sure you are connected to the router with an ethernet cable. Then upgrade your firmware through the stock firmware web interface, the process will take a few minutes. Do not interrupt the upgrade process and wait at least 2 minutes after 100% is reached.
3. The wireless LEDs should now be flashing, and if your NIC card is gigabit, you should also see one orange LAN led, if you see these your flash is complete and you can now proceed to the 30/30/30 or triple 30 reset.
4. Hold the reset button under the router for 30 seconds and do not release it, while still holding the reset button unplug the router and leave it unplugged for 30 more seconds. Still holding the reset button, plug the router back in and wait yet another 30 seconds. Unplug the router again and release the reset button, plug it back in and wait at least 2 minutes, this is critical as the router is building NVRAM settings.
5. Repeat step 4 one final time.
6. Power cycle the router, unplug it for 30 seconds and plug it back in, or use the switch. Installation is now complete.
Now that DD-WRT is fully installed and NVRAM is cleared, ensure your PC does not have any internal static IP then point your browser to 192.168.1.1, this is the DD-WRT default IP and can be changed to any IP you like. You should be at the username and password screen, set them accordingly then proceed to setting up your new DD-WRT WNDR3700.
Upgrading
To upgrade to a newer build of DD-WRT, use the web interface and selecting the "wndr3700-webflash.bin" file instead. Do not select "restore defaults" or you may have a semi bricked device. There has been many reports of that setting bricking multiple different routers yet some have no issue, so USE AT YOUR OWN RISK! You should not have to restore to defaults just from upgrading builds, to restore to defaults instead use the far superior triple 30 reset. Also, if you do partially brick your router, use this page to unbrick it.
Reverting
Jaxxit wrote:
So you've bought a shiny new wireless router for your home network and loaded it with DD-WRT. Like myself, you've decided it's just not for you and you'd rather return to the factory firmware. I've read through the forums and still found the guides a little confusing. So here's how to restore the stock or factory firmware on your Netgear WNDR3700 router in five simple and easy to understand steps.
Before you begin you will need to gather these resources:
- 1. A push pin, safety pin or needle.
- 2. A copy of the latest WNDR3700 firmware which you can download [HERE]
** NOTE: that this guide was written for the Netgear WNDR3700-100NAS Revision: 02R1 using Windows 7 64-bit. This will work for any WNDR3700 router currently running DD-WRT.
Step 1: Setting Your Static IP Address
It is important that you setup a static IP address on your computer. Navigate to: "Start" -> "Control Panel" -> "Network and Internet" -> "Network and Sharing Center" -> "Change adapter settings" (left side). Now right click on your local area connection and open up the properties window. Select "Internet Protocol Version 4 (TCP/IPv4)" and click on properties. Enter the following information then click "OK".
IP address: 192.168.1.2 Subnet mask: 255.255.255.0 Default gateway: <leave blank> Preferred DNS server: <leave blank> Alternate DNS server: <leave blank>
Step 2: Placing the Router Into Recovery Mode
Start by turning off the router using the power button on the back of the device. Now, using the small object of your choice, press and hold the "Restore Factory Settings", also known as the Reset button located on the bottom of the router (there is a red ring around it). While holding the rest button, turn the router back on. Continue to hold the reset button for approximately 45 seconds then release it.
** NOTE: Before you release the reset button, just be sure the power LED light on the router is flashing. If it isn't, continue to hold it for about another 15 seconds until it is flashing.
Step 3: Enable the TFTP Client in Windows
If you are using Windows Vista or Windows 7, you will need to enable the TFTP client. To do this, navigate to: "Start" -> "Control Panel" -> "Programs" -> "Programs and Features" -> "Turn Windows features on or off" (left side). From there, scroll down until you spot "TFTP Client". Check the box if it isnt already and click "OK". Exit the control panel.
Step 4: Flash the Firmware
Start by opening up a command prompt. From there you will want to type "cd desktop" in order to change your working directory to your desktop. Assuming of course that is where you saved the firmware download. Now for the fun bit. In the command window type:
tftp -i 192.168.1.1 put WNDR3700-V1.0.4.68NA.img
** NOTE: Be sure to use the appropriate name of the file you are trying to flash. It may be a later version then the one I used as an example.
Step 5: The Waiting Game
This would be the perfect time to go grab a drink or hit the washroom. You need to be patient. Do not turn off, restart, unplug cables or otherwise interact with your router. It may take a little while; this is normal! Watch the power LED light on the front of the router. It should remain orange throughout the process. Once it is complete, it will turn green. At this point you may proceed to point your browser to "192.168.1.1" and continue to setup your router.
Good luck!
JTAG/Serial Info
JTAG
JTAG Pinouts
This section is in need of cleanup!
JTAG Recovery
This section is in need JTAG Recovery Instructions!
Serial
Serial Pinouts
This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial Recovery
This section is in need of Serial Recovery Instructions!
USB Info
The USB port is where you can connect an external USB hard drive or flash drive. Which can do a multitude of things. You can use in as a NAS, storage for a FTP server, use Optware to run external programs like torrent software, samba for sharing files to your network, share a USB printer with your network... The list of possibilities is long, it just takes a little research.
ProFTPd is included in most the newer builds of dd-wrt. Check the features chart to be sure.
A ftp server, file sharing, and a media sever is included in TomatoUSB if your device is compatable.
vlan Info
Pictures
FCC Pictures
Notes
Known Issues
Since DD-WRT is still in beta there is some issues with the WNDR3700, having followed the proper safe procedure above, you should have minimal or no issues. If luck is not on your side then take a look at the current known most critical issues and fixes for them if there is any.
Issue 1
There has been some reports of very weak ath0/ath1 (both radios 2.4GHz and 5GHz) after flashing DD-WRT, but there is also reports of weak wireless with those that never flashed DD-WRT. The issue is still under investigation but it is probably faulty hardware related, one can only speculate the cause but it could be TX power related. Owners with this problem report the wireless is so weak one can't move any further away from the router than 1 meter. A chart has been made by a WNDR3700 owner that is linked at the bottom of this page, you have over 85% chance to get a good working router.
Fix: None short of exchanging the router for another one.
Issue 2
Some report MAC addresses changing to FF:FF:FF:FF:FF:FF, this can be caused by a improper flash. Reflash following the steps above before attempting the fix. If reflashing did not fix the problem replacing caldata should, see fix link.
Fix: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=468313#468313 (updated)
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=453998#453998 (original)
FAQ
Q: After flashing DD-WRT, the LAN LEDs are now green for 10/100M and orange 1000M?
A: This is an intentional change by the DD-WRT developers, Netgear had the colors backwards as gigabit is usually orange (check your NIC card!).
Q: I heard some WNDR3700 radios were dying shortly after flashing DD-WRT? Does the firmware damage routers?
A: No DD-WRT does not damage routers, there is also reports as said above, of WNDR3700's having weak wireless even when DD-WRT was never put on it. It is most likely a faulty hardware issue.
Q: Is there going to be a special version after DD-WRT is out of beta for this router?
A: Maybe, maybe not. Probably not because Netgear already paid for special support *for us*, this is why WNDR3700 has extra features such as RP-PPPOE server and per user/subnet/MAC QoS speed control as these are special build features.
Q: My wireless performance dropped after installing DD-WRT?
A: Refer to the Atheros wireless settings wiki page, you are probably using defaults or incorrect settings.
Q: What is the default username and password for DD-WRT?
A: Username is "root" and password is "admin".
Q: Are my wireless LEDs supposed to be flashing constantly? Stock firmware didn't do this.
A: Yes they are, that is another intentional change to DD-WRT. The slow steady flashing means the radios are on with no activity, when there is data being transferred they will rapidly flash like stock firmware.
Q: With stock firmware I was able to setup a guest AP or virtual AP, can I do this as well with DD-WRT?
A: Absolutely, and much much more!
Useful Information
- Refer to this wiki article for a guide to wireless settings for Atheros.
- Refer to this thread containing various info regarding WNDR3700.
- Refer to this thread about the possibility of different revisions of the WNDR3700, weak wireless problem could be tied to revision.
- Link to WNDR3700 revision list and which ones so far had the "radio death" problem.
Hardware Modification