FANDOM


Your here: Home / Network / Hardware Specific / Netgear / WNDR3700 v3.0


Netgear WNDR3700 v3.0
Netgear WNDR3700a
N600 WIRELESS DUAL BAND GIGABIT ROUTER

Homepage

Netgear WNDR3700

Wikipedia

Netgear

WikiDevi

WNDR3700v3

dd-wrt

Not Supported

OpenWRT

Not Supported

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = PY311200166
Industry Canada ID = 4054A-11200166
CPU Type = Broadcom BCM4718A1
MIPS Rev = ?
CPU Speed = 480MHz
Bus = ?
Flash Type = ?
Flash Chip = Macronix MX25L6445E
Flash Size = 8MB
Max Firmware Size = ?
RAM Size = 64MB
RAM Chip = Winbond W9751G6JB-25
nvram Size = ?
Switch = Broadcom BCM53115?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN
Wired Standard = IEEE 802.3/3u/3ab
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = 12VDC/2.5A
Color of LEDs = ?
Size = 8.8" x 6.0" x 1.2"
USB = 1x USB2.0
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = Broadcom BCM4718A1 (SoC)
WLAN DSP processor = ?
Antenna Connector Type = 2x2, U.FL, Internal
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Radio

Wireless Radio = Broadcom BCM4331
WLAN DSP processor = ?
Antenna Connector Type = 2x2, U.FL, Internal
Wireless Standard = IEEE 802.11a/n
WiFi Operating Frequency = 5GHz
 802.11n = up to 300Mbps
 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

Pictures

Fixme This section is in need of cleanup!

FCC Pictures

Fixme This section is in need of cleanup!

Notes


Hardware Modification


Community content is available under CC-BY-SA unless otherwise noted.