Your here: Home / Network / Hardware Specific / Planex / GW-MF54G2

Planex GW-MF54G2
Planex GW-MF54G2a












Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.


Fixme This section is in need of cleanup!


Serial Num. = ?
CPU Type = Atheros AR2317-AC1A B48218C 0622 (AR2317)
MIPS Rev = ?
CPU Speed = 180MHz
Bus = ?
Flash Type = Serial
Flash Chip = MX X070929 25L3205AMC-20G 2T850200
Flash Size = 4MB
Max Firmware Size = 3801088 bytes
RAM Size = 16MB
RAM Chip = ISSI IS42S16800A-7TL FA682618D 0645
nvram Size = ?
Switch = N/A
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = No
SD/MMC Mod Support = No
MiniPCI slots = No
PoE = ?
Power = 3.3V/1.5A
Color of LEDs = ?
Size = ?
USB = No
Serial Port = Yes
JTAG Port = No
Supported by TJTAG/Version = No
Supported by dd-wrt as of = MF54G2 v.24 pre sp2 - build 12110
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Special Features = ?

Radio (ath0)

Wireless Radio = Atheros
WLAN DSP processor = ?
Antenna Connector Type = Single Detachable Dipole 2dBi Antenna
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = 2.412GHz-2.4835GHz
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of InterestEdit


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!

JTAG/Serial InfoEdit




Serial PinoutsEdit
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XPEdit
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XPEdit
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial RecoveryEdit
Fixme This section is in need of Serial Recovery Instructions!

vlan InfoEdit

Fixme This section is in need of cleanup!


Fixme This section is in need of cleanup!

FCC PicturesEdit

Planex GW-MF54G2 FCC a Planex GW-MF54G2 FCC b Planex GW-MF54G2 FCC c

Planex GW-MF54G2 FCC d Planex GW-MF54G2 FCC e Planex GW-MF54G2 FCC f

Planex GW-MF54G2 FCC g Planex GW-MF54G2 FCC h Planex GW-MF54G2 FCC i

Planex GW-MF54G2 FCC j Planex GW-MF54G2 FCC k Planex GW-MF54G2 FCC l

Planex GW-MF54G2 FCC m Planex GW-MF54G2 FCC n Planex GW-MF54G2 FCC o

Planex GW-MF54G2 FCC p Planex GW-MF54G2 FCC q Planex GW-MF54G2 FCC r

Planex GW-MF54G2 FCC s


Hardware ModificationEdit

Community content is available under CC-BY-SA unless otherwise noted.