FANDOM


Your here: Home / Network / Hardware Specific / TRENDnet / TEW-673GRU


TRENDnet TEW-673GRU
File

Homepage

?

Wikipedia

?

dd-wrt

Not Supported

OpenWRT

Not Supported

Tomato

Not Supported

TomatoUSB

Not Supported

Gargoyle

Not Supported

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

Fixme This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = ?
CPU Type = Atheros AR7161 rev 2
MIPS Rev = MIPS 24Kc V7.4
CPU Speed = 680MHz (AHB: 170Mhz DDR:340MHz)
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 8MB
Max Firmware Size = ?
RAM Size = 64MB
RAM Chip = 2x32MB
nvram Size = ?
Switch = Realtek RTL8366 (Gigabit)
Port-based vlan = yes
802.1q vlan = yes
Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN
Wired Standard = IEEE 802.3/3u/3ab
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = no
MiniPCI slots = no
PoE = no
Power = ?
Color of LEDs = ?
Size = ?
USB = 2x
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Special Features = ?

Radio

Wireless Radio = Atheros AR9223
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g/n
WiFi Operating Frequency = 2.4 GHz
 802.11n = up to 300Mbps
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Radio

Wireless Radio = Atheros AR9220
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11a/n
WiFi Operating Frequency = 5GHz
 802.11n = up to 300Mbps
 802.11a = 6, 9, 12, 18, 24, 36, 48, 54Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

Flashing

Fixme This section is in need of cleanup!

Boot to recovery mode:

- Power off

- Push & Hold reset button

- Power on

- Wait >30 seconds

- Release reset button

- Browse to 192.168.10.1 (set own ip to 192.168.10.100)

- Upload firmware with internet explorer in 'compatability mode'.

- See blue text, percentage go from 0% to 100%

- Wait a little more after seeing 100%

- Firmware recovery flashing is done.

Upgrading

Fixme This section is in need of cleanup!

Reverting

Fixme This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts
Fixme This section is in need of cleanup!
JTAG Recovery
Fixme This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts
Fixme This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
Fixme This section is in need of Serial Recovery Instructions!

USB Info

Fixme This section is in need of cleanup!

vlan Info

Fixme This section is in need of cleanup!

switch chip supports vlans

Pictures

Fixme This section is in need of cleanup!

FCC Pictures

Fixme This section is in need of cleanup!

Notes

For DD-wrt or openwrt, can use DIR-825 firmware, just change the last byte from ascii '0' to ascii '1' with a hex editor.

Hardware Modification


Community content is available under CC-BY-SA unless otherwise noted.