WifiShadow (talk | contribs) m (→Specs: clean up, replaced: Bootloader = ? → bootloader = ?, CF Card Socket = ? → Flash Card Socket/Type = ?) |
ShadowBot-fduser (talk | contribs) m (clean up, replaced: Hardware Specific → Hardware Specific) |
||
| Line 1: | Line 1: | ||
| − | '''Your here: [[InfoDepot Wiki|Home]] / [[Network]] / [[Network |
+ | '''Your here: [[InfoDepot Wiki|Home]] / [[Network]] / [[Network - Hardware Specific|Hardware Specific]] / [[Tenda]] / W306R v2.0'''<br /> |
{{stub}}<br /> |
{{stub}}<br /> |
||
{{Infobox |
{{Infobox |
||
Revision as of 19:23, 4 May 2011
Your here: Home / Network / Hardware Specific / Tenda / W306R v2.0
 |
This article is a stub. Please help InfoDepot Wiki by expanding it, adding pictures, and improving existing text.
|
| File:TENDA_W306R_V2.JPG |
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
Specs
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = ? CPU Type = Ralink RT3052 MIPS Rev = ? CPU Speed = 380MHz? Bus = ? Flash Type = ? Flash Chip = KH29LV320DBTC-70G Flash Size = 4MB Max Firmware Size = ? RAM Size = 32MB RAM Chip = W9812G61H-75 nvram = ? Switch = ? Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-WAN 4-LAN Wired Standard = IEEE 802.3? boot_wait = ? bootloader = ? Flash Card Socket/Type = ? SD/MMC Mod Support = ? MiniPCI slots = ? PoE = ? Power = ? Color of LEDs = ? Size = ? USB = ? Serial Port = ? JTAG Port = ? Supported by TJTAG/Version = ? Supported by dd-wrt as of = ? dd-wrt K2.4 Support = ? dd-wrt K2.6 Support = ? Special Features = ?
Radio
Wireless Radio = ? WLAN DSP processor = ? Antenna Connector Type = ? Wireless Standard = IEEE 802.11b/g/n WiFi Operating Frequency = ? 802.11n = up to 300Mbps 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Links of Interest
This section is in need of cleanup!
Flashing
This section is in need of cleanup!
Upgrading
This section is in need of cleanup!
Reverting
This section is in need of cleanup!
JTAG/Serial Info
JTAG
JTAG Pinouts
This section is in need of cleanup!
JTAG Recovery
This section is in need JTAG Recovery Instructions!
Serial
Serial Pinouts
This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories -
Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
Bits per second = 115200
Data Bits = 8
Parity = none
Stop bits = 1
Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you
don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial Recovery
This section is in need of Serial Recovery Instructions!
USB Info
This section is in need of cleanup!
vlan Info
This section is in need of cleanup!
Pictures
This section is in need of cleanup!
FCC Pictures
This section is in need of cleanup!
Notes
Hardware Modification