Changes: US Robotics USR5430

Latest revision as of 00:08, 19 May 2011

Your here: Home / Network / Hardware Specific / US Robotics / USR5430

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

Specs

 This section is in need of cleanup!

Platform

Serial Num. = ?
FCC ID = MXF-EB921201G
CPU Type = Broadcom BCM4712
MIPS Rev = ?
CPU Speed = 200MHz
Bus = ?
Flash Type = ?
Flash Chip = ?
Flash Size = 2MB
Max Firmware Size = ?
RAM Size = 8MB
RAM Chip = ?
nvram = ?
Switch = ?
Port-based vlan = ?
802.1q vlan = ?
Ethernet Port Count = 1-WAN 1-LAN
Wired Standard = IEEE 802.3?
boot_wait = ?
bootloader = ?
Flash Card Socket/Type = ?
SD/MMC Mod Support = ?
MiniPCI slots = ?
PoE = ?
Power = 12V/0.5A
Color of LEDs = ?
Size = ?
USB = ?
Serial Port = ?
JTAG Port = ?
Supported by TJTAG/Version = ?
Supported by dd-wrt as of = v24 micro - 9433
dd-wrt K2.4 Support = ?
dd-wrt K2.6 Support = ?
Supported by TomatoUSB as of = ?
TomatoUSB K2.4 Support = ?
TomatoUSB K2.6 Support = ?
Special Features = ?

Radio

Wireless Radio = Broadcom
WLAN DSP processor = ?
Antenna Connector Type = ?
Wireless Standard = IEEE 802.11b/g
WiFi Operating Frequency = ?
 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps
 802.11b = 1, 2, 5.5, 11Mbps
Radio cor_rev = ?
Radio Capabilities = ?

Links of Interest

 This section is in need of cleanup!

Flashing

 This section is in need of cleanup!

Upgrading

 This section is in need of cleanup!

Reverting

 This section is in need of cleanup!

JTAG/Serial Info

JTAG

JTAG Pinouts

 This section is in need of cleanup!

JTAG Recovery

 This section is in need JTAG Recovery Instructions!

Serial

Serial Pinouts

 This section is in need of cleanup!

Hyper terminal Setup in Windows XP

In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.

Putty Setup in Windows XP

After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open

Serial Recovery

 This section is in need of Serial Recovery Instructions!

USB Info

 This section is in need of cleanup!

vlan Info

 This section is in need of cleanup!

Pictures

 This section is in need of cleanup!

FCC Pictures

 This section is in need of cleanup!

@@ Line 1: / Line 1: @@
-'''Your here: [[InfoDepot Wiki|Home]] / [[Network]] / [[Network/Hardware_Specific|Hardware Specific]] / [[US Robotics]] / USR5430'''<br />
+'''Your here: [[InfoDepot Wiki|Home]] / [[Network]] / [[Network - Hardware Specific|Hardware Specific]] / [[US Robotics]] / USR5430'''<br />
 {{stub}}<br />
 {{Infobox
@@ Line 17: / Line 17: @@
 |Row 6 title = TomatoUSB
 |Row 6 info = Not Supported
+|Row 7 title = Gargoyle
+|Row 7 info = ?
 }}
 __TOC__
@@ Line 43: / Line 45: @@
  Flash Chip = ?
  Flash Size = 2MB
+ Max Firmware Size = ?
  RAM Size = 8MB
  RAM Chip = ?
@@ Line 59: / Line 62: @@
  Power = 12V/0.5A
  Color of LEDs = ?
+ Size = ?
  USB = ?
  Serial Port = ?
@@ Line 111: / Line 115: @@
 ==JTAG/Serial Info==
- [[File:Fixme.gif]] This section is in need of cleanup!
 ====JTAG====
@@ Line 117: / Line 120: @@
 =====JTAG Pinouts=====
+ [[File:Fixme.gif]] This section is in need of cleanup!
 =====JTAG Recovery=====
@@ Line 129: / Line 134: @@
 =====Serial Pinouts=====
+ [[File:Fixme.gif]] This section is in need of cleanup!
-=====Hyper terminal Setup=====
+=====Hyper terminal Setup in Windows XP=====
  In Windows XP, Click Start Button - All Programs - Accessories -
     Communication - HyperTerminal
@@ Line 144: / Line 151: @@
               don't have to enter the settings again.
-=====Putty Setup=====
+=====Putty Setup in Windows XP=====
  After installing putty, run it
   Serial line = The COM port your using for serial (ie. COM3)
@@ Line 219: / Line 226: @@
 </div>
+==Notes==
-[[Category: English Documentation]] [[Category: US Robotics]] [[Category: Fix Me!]]
+<div class="linebox" style="border: 1px solid #404040; color: white; background-color: #222; -moz-border-radius:1em; -webkit-border-radius:1em; padding: 1em;">
+</div>
+==Hardware Modification==
+<div class="linebox" style="border: 1px solid #404040; color: white; background-color: #222; -moz-border-radius:1em; -webkit-border-radius:1em; padding: 1em;">
+</div>
+[[Category: English Documentation]]
+[[Category: US Robotics]]
+[[Category: Fix Me!]]